81N7-15011 Hyundai Excavator Component Track Adjuster Seal Kit Hydraulic Repair Seal Kit

Our main product lines applied to all Excavator brand and models, partially listed as below:
Komatsu
PC50UU, PC28UG, PC40, PC50UG, PC56, PC60, PC75, PC100, PC120, PC128UU, PC75UU, PC130, PC55MR, PC210-8, PC60-8, PC110-7, PC130-7, PC160LC-7, PC200-8, PC200LC-8, PC210LC-8, PC220-8, PC240LC-8, PC270-8, PC300-7, PC360-7, PC400-8, PC450-8

Hitachi
EX40, EX60, EX150, EX100M, EX100-2/3/5, EX120-3/5/6, EX150, EX200-1-2-3, EX220-3/5/6,
EX240, EX270, EX300-1/3/5/6, EX330, EX320-3, EX350, EX360, EX400-1/2/3/5/6, UH08, UH07, ZX55, ZX70, ZX100-1/2, ZX200, ZX210, ZX230-5, ZX240, ZX330, ZX360

C.A.T
E110B, E200B (E320), E240 (MS180), E300B, E330, D3C, D5, D5B, D5D, D6C, D6D, D6H, D7G, D8K

Daewoo
DH220, DH280, DH55-5, DH60-7, DH80GOLD, DH80-7, DH130-2, SOLARS130, DH220-2/3/5, DH200, DH225-7, DH280-3, DH258, DH215-9, DH225LC-9, DH320, DH320-2/3, DH300LC-7, DH420LC-7

Hyundai
R55-7, R55-7S, R60-7/9, R110-7, R80-7, R130LC-5, R150W-7, R150LC-7, R190LC-5, R200, R215-7, R210, R225LC-9T, R245-7, R225LC-7, R260LC-7, R265LC-7, R275LC-9T, R305LC-9T, R305LC-7, R335LC-7, R370LC-7, R385LC-9T

KATO
HD140, HD250, HD400 (HD450), HD500, HD550, HD700 ,HD770, HD800, HD820, HD850, DH880, HD1020, HD1220 HD1250, HD1430, DH1880

Kobelco
SK07N2, SK07-7, SK04-2, SK09, SK12, SK40, SK60, SK120-1/2/3, SK100-2/3, SK160, SK140, SK200, SK200-8S, SK220, SK230-6, SK260-8, SK250-8, SK260LC-8, SK210LC-8, SK300, SK320 , SK330-8, SK350LC-8, SK380D

Sumitomo
SH110, SH120, SH120-1/2/3/5, SH125X-3, SH130-3/5, SH135X-3, SH145, SH150, SH160, SH180, SH200-1/2/3, SH210-5, SH210A5, SH210LC-5, SH200LC-3, SH225X-3, SH260, SH265, SH280, SH300, SH300-2, SH330LC-3, SH330-3, SH350-5, SH350-3B, SH340, SH400, SH400-3, SH450HD-3B

SUNCARSUNCARSUNCARVO.L.VO
EB14, EB16, EC15, EC15T, EB22, EB27, EB28, EC45, EC55, EC55B, EC110, EC120, EC130, EC140, EC140B, EC145B, EC160, EC160B, EC170, EC200, EC200B

Track Adjuster Seal Kit installation requirements:
1. the hydraulic sealing gaskets and flange sealing surface should be clean

2. hydraulic sealing gasket diameter should be smaller than flange seal face outside and inside diameter should be slightly bigger than a pipe inside diameter

3. Sealing gasket pre-tightening force should not exceed the design rules

4. sealing asbestos gasket compression, it is best to use the torque wrench

5. Installing a sealing gasket, should be in order, in turn, tighten the nut

6.if there is any leakage, must be installed after antihypertensive treatment to replace or adjust the sealing gasket